DURKOPP ADLER 867 - 190322 - M GOLD

- Triple foot and tooth transport

- Large hook (26mm bobbin)

- Cutting the thread

- Programmable initial and final locking

- Speed reduction system with increased stepping height

- Maximum thread thickness 10/3Nm

- Maximum stitch length up to 12mm (Two separate adjustments that can be switched at any time)

- Foot lifting height up to 20mm

- Adjustable feet stroke up to 9mm

- Needle bar arm length 335mm

- Maximum number of stitches per minute 3800

- 230V motor - Efka Variocontrol 820 control

- Compressed air is needed to operate the machine

Video of the work of such a model: https://www.youtube.com/watch?v=OfwZwB9yQrA&t=3s

The machine is in perfect technical condition - ready to work

Fortuna UA 305 surface splitting machine - leather splitting machine

Working area: 30cm

The machine is equipped with:

- adjustment of the thickness of the material division

- two speeds of material feeding

- dust extractor and waste basket

Full manufacturer's documentation for the machine

Machine in very good condition after service

Strobel 410 - 1EV

With this machine, the insoles are sewn to the upper with a strong overcast stitch. Unlike the traditional method, the Strobel method saves a lot of material. On this machine, we can sew insoles in leather and textile footwear. The shirring device facilitates the insertion operation.

Stitch type: single thread, overcast

Double roller transport

Stitch length: 3 - 8 mm adjustable

The machine is in very good technical condition

Fortuna UAF 470 surface splitting machine - leather splitting machine

Working area: 47cm

It has an automatic knife access

Three material feeding speeds

Feeding material on two rollers

The machine is in very good technical condition after a general service

Strobel 141 - 23EV

With this machine, the insoles are sewn to the upper with a strong overcast stitch. Unlike the traditional method, the Strobel method saves a lot of material. On this machine, we can sew insoles in leather and textile footwear with a total thickness of the sewn layer up to 7 mm. The shirring device facilitates the insertion operation.

Stitch type: single thread, overcast

Stitch length: 3 - 8 mm adjustable

Needle system: 134

230V energy-saving motor

The machine is in very good technical condition

DURKOPP ADLER 867 - 190322 - M GOLD

- Triple foot and tooth transport

- Large hook (26mm bobbin)

- Cutting the thread

- Programmable initial and final locking

- Speed reduction system with increased stepping height

- Maximum thread thickness 10/3Nm

- Maximum stitch length up to 12mm (Two separate adjustments that can be switched at any time)

- Foot lifting height up to 20mm

- Adjustable feet stroke up to 9mm

- Needle bar arm length 335mm

- Maximum number of stitches per minute 3800

- 230V motor

- Compressed air is needed to operate the machine

Video of the work of such a model: https://www.youtube.com/watch?v=OfwZwB9yQrA&t=3s

The machine is in perfect technical condition - ready to work

Durkopp Adler 269

Arm machine

1 - needle

- triple foot transport

- large hook

- manual reverse

- power supply 380V

The machine is in very good technical condition

18 tons of pressure

Table dimensions: 800mm x 450mm

Hammer dimensions: 325mm

Very fast and strong

Simple intuitive operation

The machine is in very good condition after the service

Video of the machine in operation: https://www.youtube.com/watch?v=hjuW3MVylg4

The OMAC 600 R linear wrapping machine is equipped with a cold wrapping system for handbags, bags, wallets, diaries, business card holders, etc. Leather and other materials are processed with the equipment.

Features of the OMAC 600R edge bender:

material thickness from 0.2 to 2.0 mm,

bending width adjustment in the range of 4-10 mm,

pressure time adjustment from 0.3 to 10 sec.,

LCD display, microprocessor, self-diagnosis system, programmable

The machine is in very good technical condition

Atom Bridge Cutting Machine HS588/10 hydraulic press

Pressure 30 Tons

Simple, intuitive operation with the function of automatic departure after cutting

Table dimensions: 2000mm x 750mm

Hammer dimensions: 750mm x 750mm

Maximum hammer stroke: 150mm

Maximum clearance between hammer and table: 188mm

Motor power: 1.87kW

Weight: 2270kg

Full dimensions of the machine: 2380mm x 1660mm x 2300mm

The machine is in perfect technical condition after full service

Video of the machine in operation: https://www.youtube.com/watch?v=3DUrnwg86mI

Ormac 833 T - programmable computer hydraulic tip stud puncher

- electro-hydraulic programmable machine

- the machine has 9 towing jaws

- equipped with glue markers

The machine is equipped with a system that allows the assembly of any type of shoe in any size at no extra cost. All times, adjustments and machine functions are easily programmed via the touchscreen, reducing start and changeover times. Up to 100 programs can be stored.

Year of manufacture: 2015

The machine is in perfect technical condition, like new!

Video of the machine in operation: https://www.youtube.com/watch?v=GSpu80-QNa8