Sagitta

Sagitta

Active filters

A new rubber splitting machine from the renowned Italian manufacturer Sagitta

Video: https://www.youtube.com/watch?v=s-UiiH9VvtU

Technical Data
Maximum cutting thickness 8 mm.
Minimum cutting thickness 0,5 mm.
Control panel with digital thickness indicator
Manual Knife positioning
Sharpening device pressure adjustable with micrometric drive
Three manual feed speeds (1,1 – 1,8 – 2,6 mt./min.)
Knife tension indicator
Self adjusting knife guide plate
Upper and lower motor driven steel feed rollers
High precision knife guides
Optical device to control the chamfer position and symmetry
Automatic lubrication bandknife
Maximum absorbed power 2 kW
Three-phase power supply 400 Volt 50/60 Hz.

Folding Machine

Video: https://www.youtube.com/watch?v=jU3m1rAIOVc&t=1s

Upper thermocementing and folding machine, photocells controlled, complete with table and clutch motor.
Automatic controls by photocells:
– cement fow and adjustable delay
– feeding for external curves with progammable delay according to the speed
– feeding for internal curves with progammable delay according to the speed and automatic cutting with adjustable step
– easy selection of photosensor according to the geometry of the working leather uppers.

Computerised thermocementing and folding machine with photocells and microprocessors. It is able to fit the requirements of any single operator since this machine is able to self store commands while making the first piece of work and then repeat these ones accurately leaving to the operator only the task to guide the piece of work. The RP NOVA V4 controls the glue flow very accurately and delivers it inside the folding, in thread shape. At the end of each working cycle, the machine stops with the hammer in an open position and sets in the automatic glue suction, preventing the glue from falling down on the upper and consequently stain it.

The sturdiness and simplicity of the machine guarantees trouble free operation in mass production.

MB10 driven by electronic motor, which allows to vary speed. It is therefore suitable for the most part of perforating works.

MB S driven by normal motor, with fixed speed and perforating rod automatic stop.

Video: https://www.youtube.com/watch?v=xfjGtLKd_mQ

Machine to make holes for shoe laces. It is possible to make the holes on both sides of uppers simultaneously and to select, by moving the pressing truck, the quantity of the holes to be made up to a maximum of 7 holes each side. It is possible to adjust the alignment of the holes by means of 2 levers on both sides of the machine head and by means of a knob placed on the right side of the machine. It is possible to adjust the distance between the holes from a minimum of abt 10 mm and a maximum of abt 19 mm. from a centre to another. The set of 7 perforators composed by punches and dies, can be selected among 10 different sizes from 1.8 mm and 4.8 mm.

Video: https://www.youtube.com/watch?v=VFfGYrYIWHg

Eyeletting Machine

Perforating and eyeletting machine with hand-protection device, to apply eyelets from 4 to 12 mm., with adjustable raceway, complete with table, motor and one set of dies. This machine is equipped with an adjustable raceway wich avoids the replacement of the hopper and it’s relevant raceway when it is necessary to change the size of the eyelet. The punch, the upper and lower die wich apply the eyelet are the only parts that you have to replace according to the size of the eyelet, their replacement is very rapid. The lower die is adjustable in height to compensate the different thickness of material on wich the eyelet has to be applied. Must be used an eyelet able to perforate
Video: https://www.youtube.com/watch?v=kJEuc28hSvU&t=1s

Double Feeding Self Piercing Eyeleting Machine to apply eyelets with washer (Max shank diameter 8 mm.). The machine is provided with a piercing device by cam with a precise and easy adjusting to assure good cutting for each material. All the functions are under the conrol of a microprocessor, a partial counter with reset and a total counter are available. Among the optoins a slow motion for TEST and a MULTIPLE SETTING to repeat a programmable sequence of a certain number of eyelets and the time between the setting.

Video: https://www.youtube.com/watch?v=E7J_W5P6UB0

Double Feedng Attaching Machine for jeans rivets & buttons.
The lower feeder is suitable for several types of nail and this exalts the very advance flexibility of the machine. Thanks ti this possible , by replacing the upper feeder, to set both jeans buttons and jeans rivets of different type. All the functions are under the control of a microprocessor, a partial counter with reset  and total counter are available. Among the options a slow motion for TEST and a MULTIPLE SETTING to repeat a programmable sequence of a certain number of eyelets and the time between the setting.

Video: https://www.youtube.com/watch?v=P9WRLvWfczE